ODSTRANENIE pripadne OBMEDZENIE INPUTLAGU

[SpiriT]

Hola

Mam taky mensi problem kupil som monitor Samsung 215TW, plne pri vedomi a vedomy toho ze ma dost velky inputlag, okolo 50ms (+/- zalezi od kusu a nastaveni)

Takze som myslel ze to nebude az take zle, ale opak bol pravdou, nevravim ze kvoli tomu idem ten monitor vratit, ale pri niektorych hrach to fakt vadi, hlavne pri rychlich FPS a pri automobilovych pretekoch, jednoducho je poznat ze zvuk ide nepatrne popredu oproti obrazu ...

Takze pocul som par ludi sa vychvalovat ze oni takyto problem nemaju (alebo si len myslia ze nemaju), alebo ze ho odstranili, pripadne vyrazne obmedzili, takze moja otazka smeruje prave knim, ..

AKO SA DA (ZEVRAJ POMOCOU OVLADACOU KU GK) ODSTRANIT, OBMEDZIT INPUTLAG ?


/// Viem ze je podomnou tema LCD a Inputlag, ale to je skor informacny topic, tak prosim uzivatelou, ktory maju s tym skusenosti nech sa pochvalia

/// Dakujem za postrehy ...

[Bonta-kun]

ja som velmi nic neriesil. ani som nemusel, bud mam lepsi kus alebo som k nemu menej vnimavy.. neviem. ale nieco som predsa menil v nastaveniach.. aj na nete bol navod k tomu. mrknem sa a dam vediet. a inak ze pri mode internet(ma aj najlepsie nastavenie- subjektivne) je lag najmensi zevraj ale ja ho fakt nijak nepozorujem,trochu zozaciatku

[Bonta-kun]

tu som nieco nasiel, tak mozes skusit:
Input lag is the LCD's only problem. Some have no issues and some have severe problems. Myself, I had some input lag but it was minimal. I did research and found ways to 99% eliminate the input lag. Here goes:


LCD's should only be used with cord mice, not cordless. Make sure your mouse is a newer laser/optical model that is USB and supports up to 2000DPI. I bought the Razor CopperHead (Blue - tempest) and it is so much better than my older Logitech cordless setup (LX 700) its like night and day. Games run fine with no input lag or its so minimal now, I can barely notice it. I also bought a standard MS cord USB keyboard.

Tweaks:

After enabling coolbits, go to Additional Direct3D settings and change the default value from 3 to 2. Helps with dual core CPU's. You can try 1 or 0 but this will result in game performance issues. So 3 or 2 is best. "Update, I use the default setting of 3."

Make sure your video card/LCD's VSync is ON.

Disable Triple Buffering as well.


Now I can play games with no noticeable input lag.

- Quake 4
- FEAR
- Far Cry
- Half Life 2
- Call of Duty 2
- Elder Scrolls 4 Oblivion
- Dungeon Siege 2
- Prey
- WarCraft 3
- BF1942
- NeverWinter Nights 2


Without these tweaks and new mouse and keyboard, yeah the input lag is annoying for some.

Oh, since I have the Razor CopperHead, I use the profile 3 which is 800 DPI / 500 Hz. For me, more than 800 DPI is too much for gaming.


I have the following hardware:

A8N-E
2GB dual channel
A64 x2 3800+
7800GT CO
DiamondMax 300GB SATA 16MB NCQ drive
SB X-FI ExtremeMusic
Samsung 215TW
LG H22N
Razor CopperHead (800 DPI / 500 Hz used - profile 3)
Standard new MS corded USB keyboard

This message was modified by the poster at 12 16, 2006 12:49 PM

[SpiriT]

Jo, diky kamo, hned ako dofrcim domov (az piatok, tyzdnovky, vies ako ...) tak to testnem a dam vediet, zatial vrela vdaka

[Bonta-kun]

neni zac, pozri este toto potom:
http://www.svethardware.cz/disc_doc-N89 ... tml?&all=1 na konci debaty tam je par navodov.

[BurnerTom]

Caute.
Pred par dnami som kupil 215TW, skusal som BattleField2, FlatOut 2 - nezbadal som ziaden problem - zajtra idem fotit CRT a LCD vedla seba so stopkami tak sa uvidi kolko tam skutocne je. Mam model z marca 2007. Ako sa da zistit verzia firmwaru?

[Bonta-kun]

to netusim.. ale na test som zvedavy

[Sheep221]

Caute.
Pred par dnami som kupil 215TW, skusal som BattleField2, FlatOut 2 - nezbadal som ziaden problem - zajtra idem fotit CRT a LCD vedla seba so stopkami tak sa uvidi kolko tam skutocne je. Mam model z marca 2007. Ako sa da zistit verzia firmwaru?

myslis nejaku verziu firmwaru monitora?ak ano tak vie to zistit tusim program powerstrip, avsak vacsina LCD monitorov ktore maju len analogovy VGA vstup sa zistit nedaju alebo sa zobrazia chybne udaje

[BurnerTom]

Dnes som meral/fotil a ... 50ms.
Nech som nastavil absolutne hocico tak stale okolo 50ms takze sa mi az nechce verit, ze tie nastavenia v CCC funguju

[BurnerTom]

Nainstaloval som PowerStrip a nikde tam verziu FW nevidim - je tam len toto:
Vyrobca: Samsung
Model ID: SyncMaster
Seriove cislo: HS1P302534
Datum vyroby: 2007, ISO week 13

[Bonta-kun]

hmm, nic moc teda. ale balik to nejak dokazal:
http://www.balik123.ic.cz/?page=samsung_215tw
http://www.balik123.ic.cz/img/lcd/input.jpg

[SpiriT]

no ja som nameral 40 az 60 ms, vzavislosti od zvoleneho profilu (game, internet, text, sport ... ), zevraj sa to da obmedzit

Mrkni do nastaveni forceware a jestli je pod Performance & Quality settings polozka Additional Direct3d settings.
Pokud ano, tak zkus dat 2 nebo 1, 0 uz pøilis redukuje vykon.

Jestli tam ta polozka neni tak ji aktivuj v programu NVTweak
http://downloads.guru3d.com/download.php?det=911

ale akosi sa nedokazem dostat ku klasickej ponuke, mam iba tu rozsirenu, nevie niekto ako to prepnut do klasickej ?




Klasicka ponuka vyzera takto + odomktnute additional 3D settings