Haswell 4770k

[xsi69]

Takze asi 4,3ghz premna

[Eddward]

1,25V je kde napisane? lebo inak blbost, kludne aj 1,3V pokial to vies uchladit neni sa coho bat

No neviem, momentalne mam v IBT do 90 a viac to nehrotim pokial nedam dole pastu, ale to aj tak az po zaruke. Zatial som spokojny, mohlo to byt aj horsie.

do 90C v IBT v tomto teple je velmi dobra teplota
skus to prehnat beznymi aplikaciami, pripadne taky CineBench R11.5 postaci, nakolko to vylezie... inak celkovo myslim ze super kus,
a hod sem pls batch cislo co je na krabici
zda sa ze L310xxxx su na tom najlepsie momentalne, tak ci si chytil tiez z tej varky

[CageJ]

Nie je to blbost... da sa najst oficial specs od Intelu.

[Mimiik]

L309B384

Vcera po vymene modulov za tie kingstony sa mi teplota brutane dvihla, pustil som ibt a teplota jeb na 100C. Skusim dat z5 stary modul, neviem cim to je avsak musim to zistit. Docasne 4.2/1.07V -30 offset. Ano teploty su rovnake, dvihaju sa frekvenciou, neviem cim to bude.

[pipo137]

tak ak si dal nove ram (teda mas viac GB pamate) a testujes v IBT na max, tak je pochopitelne, ze aj teploty trochu poskocili, kedze potom uz ten test trva dlhsie a teda aj zataz je vacsia

PS: A do tych 1,3V by som sa nebal ist

[Mimiik]

Nie nie hned ked to zapnem to vyleti ku 100vke, dal som aj single staru pamat a robi to to iste. Vo stvrtok vecer to slo normalne, vcera som prisiel z prace, zapol kompa a zhrozil som sa.

Aha uz viem co to robi. S manual V na 1.18V mam teploty normalne, ked nastavim moznost Adaptive, aby uberalo V s podtaktovavanim cpu/offset tak mi tie teploty v burne stupnu k takymto vyskam aj ked neviem preco ked V je uplne rovnaky

[Eddward]

cital som niekde ze s adaptive napätim pri programoch s AVX doska pusta do CPU o 0.1V viac
ci je to bug/ficura dosky/cpu neviem zatial...
taktiez pre Haswell je vraj najlepsi test stability najnovsia AIDA

[Mimiik]

Neviem, teploty by sedeli ale stabilita nie :/ ked to dam nizsie tak to padne, ak to mam na manual Voltage tak to drzi na tej hranici co aj s adaptive, ak pri adaptive znizim V tak to padne a tak isto aj pri manual.

H100i mam konecne pri sebe, doma nahodim a uvidim jak to bude ficat nevie niekto ako je na tom corsair s tou ich 5 year warranty? treba sa niekde regnut alebo pod?

No LOL teploty v burne rovnake, v idle nizsie o cca 10C. Je to trapas. Fakt to chce dat dole pastu alebo ostanem na 4.4 1.13V

[flanker]

cital som niekde ze s adaptive napätim pri programoch s AVX doska pusta do CPU o 0.1V viac
ci je to bug/ficura dosky/cpu neviem zatial...
taktiez pre Haswell je vraj najlepsi test stability najnovsia AIDA

dá se to tak říci...Pokud je nějaký skutečně brutální test, který nemá co do činění s realým užitím, adaptive mírně nastaví vyšší napětí. Nicméně pokud pojedeš rendering, mělo by se to chovat jinak a napětí být v mezích a tím pádem i teploty....

Haswelly umírají jak na běžícím pásu Toto je výpis příspěvků za včerejšek z XS...

"Same here George :/ , 3 out of 6 cpus already died on me. First one at 1.92v. Running wprime 1024 at 5700Mhz on cascade -110c Load on Z87-Pro , screen went blank , code 00. Second died Running 3DMark06 at 5936Mhz in the second cpu test I got bsod then only code 71 on M6E @ -110c load 1.85v. Third just died 2 days ago running Cinebench 11.5 at 5.4Ghz at only 1.72v. -110c this retail cpus are very very fragile. Now im scared to push more than 1.76v on my good 4670K 6.2Ghz cpu , I don't want to kill it so soon , so far Retail Haswell not looking good."

"A friend has bought an 4770K and it's not doing more than 4.2ghz because it requires 1.28v and it start to throttle?"

"I think mine is heaving same symptoms as well ->71 and I only raised iod .270 and VCCIN 2.1 (first it was stable 32M (PSC)2600 tight and after first 71 code it wouldn't do it again with loose timings )..Haswell looks more and more like a FAIL"

"one of my best cpu is dead too , he died for no reason on phase , first code 40 and reboot cod 00...., i think intel is very happy with the haswell Rma rate=)))
if we remember at the past , before (2-3 monts)haswell launch..rumors that incredible arhitecture can hint on Ln2 8ghz and more..."

Well not quite sure, I just know that I set 2.5 input booted at 5Ghz, then while at -130c pulled raised vcore to 1.75v and started raising multi and when I got to x59, it rebooted and now it will hang on 71 if you try to oc, even 5Ghz, at any voltage. Flashed bios, tried more voltage for everything (pch included) at 5Ghz, memory at 2400. . . all result in hang on 71, pch initialization error I think as that is what is displayed on the OLED.

"I think something is damaging the DMI, because this has happened on another cpu on a different board, except the cpu would show 71, then reboot constantly while this one will run fine at 4Ghz but anything higher than that will not post. The other cpu I killed hung on 78 a bit different.
All ES cpu's are still alive and well."

[CageJ]

Flanker a tvoj LN2 test ?

[Mimiik]

Myslim ze moj kusok by dal 5ghz do 1.35V ale uchladit to je nemozne

[xsi69]

Si vychitil daky moc dobry kus .
Moj ide na 4,5ghz pri 1,3V , ale rock stable s teplotami do 85°C .
4,85ghz pri 1,36V som v pohode nabootoval do win len v zatazi mal 95+°C a throttloval .

[pipo137]

xsi69: Ty sa v tom prípade tiež moc nemôžeš sťažovať

[xsi69]

Pravda .
Ale mať 4,5ghz na 1,3V alebo 1,17V je docela rozdiel

[pipo137]

to hej... ale myslel som to tak, že ty aspoň máš tých 4,5GHz
...na rozdiel od iných