Mikrotik - pre zaciatocnikov

[Jerry]

Aha, ospravedlňujem sa, to mi trocha uniklo. Ok, tak dĺžka kábla, aký je to kábel, či má tienenie, čo ukazuje mikrotik akú má chytenu rýchlosť, chybovost (packet los) atd ... Daj bližšie informácie. V logu by tiež niečo mohlo byť, keby ma daný interface problém, skús pozrieť.

[Pavoluhliarik]

kabel cat 7 klasicky dlžka 2 m v logu nevypisuje pri xboxe žiadne problémi vypisuje, že má 1 gb sietovku
OEM S/FTP patchkabel Cat 7, s konektormi RJ45, LSOH, 2 m, zelený tienený
ether4 link up (speed 1G, full duplex)-xbox - iné veci nevypisuje

[Jerry]

Tak potom si črep žije vlastný život, ešte by som skúsil vymeniť kábel, ale to je podľa mňa zbytočné. Asi si xbox nerozumie s mikrotikom. Ešte by som vyskúšal jednu vec, keby si mal gigovy switch, tak strcit to medzi nich, že či by bol výsledok rovnaký ...

[Pavoluhliarik]

Ja si myslím, že si nerozumie s mikrotikom lebo mám overené od iného, že na inom routri gpo huawei to ide on má 500 ide 500.
Môžem použiť aj tento https://www.alza.sk/tp-link-litewave-ls ... 711597.htm

[mp3turbo]

cat7 je prekvapenie, ale to by malo chodit na plne bomby. Ten switch je podla mna zbytocny. Daj zo srandy tieto info :

[adm@kumbal] > /interface ethernet print detail
Flags: X - disabled, R - running, S - slave
0 R ;;; orange-siet
name="ether1" default-name="ether1" mtu=1500 l2mtu=1598 mac-address=74:4D:28:BB:69:31 orig-mac-address=74:4D:28:BB:69:31 arp=enabled arp-timeout=auto loop-protect=default loop-protect-status=off loop-protect-send-interval=5s
loop-protect-disable-time=5m auto-negotiation=yes advertise=10M-half,10M-full,100M-half,100M-full,1000M-half,1000M-full full-duplex=yes tx-flow-control=off rx-flow-control=off speed=1Gbps bandwidth=unlimited/unlimited
switch=switch1

1 ;;; kumbal-NAS
name="ether2" default-name="ether2" mtu=1500 l2mtu=1598 mac-address=74:4D:28:BB:69:32 orig-mac-address=74:4D:28:BB:69:32 arp=enabled arp-timeout=auto loop-protect=default loop-protect-status=off loop-protect-send-interval=5s
loop-protect-disable-time=5m auto-negotiation=yes advertise=10M-half,10M-full,100M-half,100M-full,1000M-half,1000M-full full-duplex=yes tx-flow-control=off rx-flow-control=off speed=1Gbps bandwidth=unlimited/unlimited
switch=switch1

2 ;;; tv
name="ether3" default-name="ether3" mtu=1500 l2mtu=1598 mac-address=74:4D:28:BB:69:33 orig-mac-address=74:4D:28:BB:69:33 arp=enabled arp-timeout=auto loop-protect=default loop-protect-status=off loop-protect-send-interval=5s
loop-protect-disable-time=5m auto-negotiation=yes advertise=10M-half,10M-full,100M-half,100M-full,1000M-half,1000M-full full-duplex=yes tx-flow-control=off rx-flow-control=off speed=1Gbps bandwidth=unlimited/unlimited
switch=switch1

3 R ;;; tatko
name="ether4" default-name="ether4" mtu=1500 l2mtu=1598 mac-address=74:4D:28:BB:69:34 orig-mac-address=74:4D:28:BB:69:34 arp=enabled arp-timeout=auto loop-protect=default loop-protect-status=off loop-protect-send-interval=5s
loop-protect-disable-time=5m auto-negotiation=yes advertise=10M-half,10M-full,100M-half,100M-full,1000M-half,1000M-full full-duplex=yes tx-flow-control=off rx-flow-control=off speed=1Gbps bandwidth=unlimited/unlimited
switch=switch1

4 R ;;; mato
name="ether5" default-name="ether5" mtu=1500 l2mtu=1598 mac-address=74:4D:28:BB:69:35 orig-mac-address=74:4D:28:BB:69:35 arp=enabled arp-timeout=auto loop-protect=default loop-protect-status=off loop-protect-send-interval=5s
loop-protect-disable-time=5m auto-negotiation=yes advertise=10M-half,10M-full,100M-half,100M-full,1000M-half,1000M-full full-duplex=yes tx-flow-control=off rx-flow-control=off speed=1Gbps bandwidth=unlimited/unlimited
switch=switch1


zrejme mas standartne zapnute auto-konfiguracie rychlosti aj duplexu, hlavne v tom duplexe castokrat vidim problemy - co sme sa nabohovali medzi Ciskami a Intelmi






[adm@kumbal] > /interface ethernet print stats detail

name: ether1 ether2 ether3 ether4 ether5
driver-rx-byte: 526 519 325 323 0 0 224 447 426 708 7 326 379 457
driver-rx-packet: 504 393 961 0 0 249 730 188 57 687 784
driver-tx-byte: 94 463 301 853 0 0 342 962 469 985 207 272 640 531
driver-tx-packet: 236 880 361 0 0 290 444 710 167 262 080
rx-bytes: 527 126 833 176 0 0 225 470 464 871 7 567 080 450
rx-too-short: 0 0 0 0 0
rx-64: 9 446 907 0 0 11 243 638 20 593 664
rx-65-127: 30 621 678 0 0 77 774 737 28 513 484
rx-128-255: 93 619 888 0 0 5 773 597 4 272 085
rx-256-511: 12 626 950 0 0 1 117 282 2 658 236
rx-512-1023: 16 269 728 0 0 13 614 104 370 220
rx-1024-1518: 343 799 554 0 0 140 240 712 1 390 096
rx-1519-max: 0 0 0 0 0
rx-too-long: 0 0 0 0 0
rx-broadcast: 60 338 0 0 18 490 2 217
rx-pause: 0 0 0 0 0
rx-multicast: 354 503 0 0 52 591 7 337
rx-fcs-error: 0 0 0 0 1
rx-align-error: 0 0 0 0 0
rx-fragment: 0 0 0 0 0
rx-overflow: 51 0 0 0 0
tx-bytes: 95 410 822 547 0 0 344 124 248 324 207 941 621 088
tx-64: 35 423 209 0 0 3 252 104 5 911 259
tx-65-127: 103 572 369 0 0 26 812 627 8 441 605
tx-128-255: 30 485 585 0 0 23 376 243 4 642 160
tx-256-511: 5 120 234 0 0 2 250 504 4 889 317
tx-512-1023: 14 441 026 0 0 10 888 174 3 740 475
tx-1024-1518: 47 837 929 0 0 223 865 054 139 637 020
tx-1519-max: 0 0 0 0 0
tx-too-long: 0 0 0 0 0
tx-broadcast: 46 067 0 0 8 679 73
tx-pause: 0 0 0 0 0
tx-multicast: 0 0 0 0 0
tx-underrun: 0 0 0 0 0
tx-collision: 0 0 0 0 0
tx-excessive-collision: 0 0 0 0 0
tx-multiple-collision: 0 0 0 0 0
tx-single-collision: 0 0 0 0 0
tx-excessive-deferred: 0 0 0 0 0
tx-deferred: 0 0 0 0 0
tx-late-collision: 0 0 0 0 0


len tak zo srandy...

[Pavoluhliarik]

[admin@MikroTik] > interface ethernet print detail
Flags: X - disabled, R - running, S - slave
0 R name="ether1" default-name="ether1" mtu=1500 l2mtu=1592 mac-address=74:4D:28:D7:63:DE orig-mac-address=2C:C8:1B:AB:96:46 arp=enabled arp-timeout=auto loop-protect=default
loop-protect-status=off loop-protect-send-interval=5s loop-protect-disable-time=5m auto-negotiation=yes
advertise=10M-half,10M-full,100M-half,100M-full,1000M-half,1000M-full full-duplex=yes tx-flow-control=off rx-flow-control=off speed=1Gbps bandwidth=unlimited/unlimited
switch=switch1

1 RS ;;; Mac mini
name="ether2" default-name="ether2" mtu=1500 l2mtu=1592 mac-address=2C:C8:1B:AB:96:47 orig-mac-address=2C:C8:1B:AB:96:47 arp=enabled arp-timeout=auto
loop-protect=default loop-protect-status=off loop-protect-send-interval=5s loop-protect-disable-time=5m auto-negotiation=yes
advertise=10M-half,10M-full,100M-half,100M-full,1000M-half,1000M-full full-duplex=yes tx-flow-control=off rx-flow-control=off speed=1Gbps bandwidth=unlimited/unlimited
switch=switch1

2 RS ;;; Samsung tv
name="ether3" default-name="ether3" mtu=1500 l2mtu=1592 mac-address=2C:C8:1B:AB:96:48 orig-mac-address=2C:C8:1B:AB:96:48 arp=enabled arp-timeout=auto
loop-protect=default loop-protect-status=off loop-protect-send-interval=5s loop-protect-disable-time=5m auto-negotiation=yes
advertise=10M-half,10M-full,100M-half,100M-full,1000M-half,1000M-full full-duplex=yes tx-flow-control=off rx-flow-control=off speed=1Gbps bandwidth=unlimited/unlimited
switch=switch1

3 RS ;;; Xbox serie x
name="ether4" default-name="ether4" mtu=1500 l2mtu=1592 mac-address=2C:C8:1B:AB:96:49 orig-mac-address=2C:C8:1B:AB:96:49 arp=enabled arp-timeout=auto
loop-protect=default loop-protect-status=off loop-protect-send-interval=5s loop-protect-disable-time=5m auto-negotiation=yes
advertise=10M-half,10M-full,100M-half,100M-full,1000M-half,1000M-full full-duplex=yes tx-flow-control=off rx-flow-control=off speed=1Gbps bandwidth=unlimited/unlimited
switch=switch1

4 RS ;;; Asustor
name="ether5" default-name="ether5" mtu=1500 l2mtu=1592 mac-address=2C:C8:1B:AB:96:4A orig-mac-address=2C:C8:1B:AB:96:4A arp=enabled arp-timeout=auto
loop-protect=default loop-protect-status=off loop-protect-send-interval=5s loop-protect-disable-time=5m auto-negotiation=yes
advertise=10M-half,10M-full,100M-half,100M-full,1000M-half,1000M-full full-duplex=yes tx-flow-control=off rx-flow-control=off speed=1Gbps bandwidth=unlimited/unlimited
switch=switch1

5 S name="ether6" default-name="ether6" mtu=1500 l2mtu=1592 mac-address=2C:C8:1B:AB:96:4B orig-mac-address=2C:C8:1B:AB:96:4B arp=enabled arp-timeout=auto loop-protect=default
loop-protect-status=off loop-protect-send-interval=5s loop-protect-disable-time=5m auto-negotiation=yes
advertise=10M-half,10M-full,100M-half,100M-full,1000M-half,1000M-full full-duplex=yes tx-flow-control=off rx-flow-control=off speed=1Gbps bandwidth=unlimited/unlimited
switch=switch2

6 S name="ether7" default-name="ether7" mtu=1500 l2mtu=1592 mac-address=2C:C8:1B:AB:96:4C orig-mac-address=2C:C8:1B:AB:96:4C arp=enabled arp-timeout=auto loop-protect=default
loop-protect-status=off loop-protect-send-interval=5s loop-protect-disable-time=5m auto-negotiation=yes
advertise=10M-half,10M-full,100M-half,100M-full,1000M-half,1000M-full full-duplex=yes tx-flow-control=off rx-flow-control=off speed=1Gbps bandwidth=unlimited/unlimited
switch=switch2

7 S name="ether8" default-name="ether8" mtu=1500 l2mtu=1592 mac-address=2C:C8:1B:AB:96:4D orig-mac-address=2C:C8:1B:AB:96:4D arp=enabled arp-timeout=auto loop-protect=default
loop-protect-status=off loop-protect-send-interval=5s loop-protect-disable-time=5m auto-negotiation=yes
advertise=10M-half,10M-full,100M-half,100M-full,1000M-half,1000M-full full-duplex=yes tx-flow-control=off rx-flow-control=off speed=1Gbps bandwidth=unlimited/unlimited
switch=switch2

8 S name="ether9" default-name="ether9" mtu=1500 l2mtu=1592 mac-address=2C:C8:1B:AB:96:4E orig-mac-address=2C:C8:1B:AB:96:4E arp=enabled arp-timeout=auto loop-protect=default
loop-protect-status=off loop-protect-send-interval=5s loop-protect-disable-time=5m auto-negotiation=yes
advertise=10M-half,10M-full,100M-half,100M-full,1000M-half,1000M-full full-duplex=yes tx-flow-control=off rx-flow-control=off speed=1Gbps bandwidth=unlimited/unlimited
switch=switch2

9 S name="ether10" default-name="ether10" mtu=1500 l2mtu=1592 mac-address=2C:C8:1B:AB:96:4F orig-mac-address=2C:C8:1B:AB:96:4F arp=enabled arp-timeout=auto
loop-protect=default loop-protect-status=off loop-protect-send-interval=5s loop-protect-disable-time=5m auto-negotiation=yes
advertise=10M-half,10M-full,100M-half,100M-full,1000M-half,1000M-full full-duplex=yes tx-flow-control=off rx-flow-control=off speed=1Gbps bandwidth=unlimited/unlimited
switch=switch2 poe-out=auto-on poe-priority=10 power-cycle-ping-enabled=no power-cycle-interval=none

10 S name="sfp-sfpplus1" default-name="sfp-sfpplus1" mtu=1500 l2mtu=1600 mac-address=2C:C8:1B:AB:96:50 orig-mac-address=2C:C8:1B:AB:96:50 arp=enabled arp-timeout=auto
loop-protect=default loop-protect-status=off loop-protect-send-interval=5s loop-protect-disable-time=5m auto-negotiation=yes advertise="" full-duplex=yes
tx-flow-control=off rx-flow-control=off speed=10Gbps bandwidth=unlimited/unlimited sfp-rate-select=high sfp-shutdown-temperature=95C

[admin@MikroTik] >

[admin@MikroTik] > interface ethernet print stats
name: ether1 ether2 ether3 ether4 ether5 ether6 ether7 ether8 ether9 ether10 sfp-sfpplus1
driver-rx-byte: 24 165 343 399 13 362 452 578 286 665 116 767 068 769 42 961 348 402 0 0 0 0 0 0
driver-rx-packet: 17 415 102 36 281 880 3 889 953 779 499 32 301 356 0 0 0 0 0 0
driver-tx-byte: 1 646 938 764 54 632 063 342 10 696 703 837 1 336 817 129 13 018 215 249 0 0 0 0 0 0
driver-tx-packet: 7 397 723 40 409 196 7 392 832 1 391 489 34 372 201 0 0 0 0 0 0
rx-bytes: 24 235 003 807 13 507 579 286 303 023 340 770 186 765 43 090 553 826 0 0 0 0 0 0
rx-packet: 0
rx-too-short: 0
rx-64: 0
rx-65-127: 0
rx-128-255: 0
rx-256-511: 0
rx-512-1023: 0
rx-1024-1518: 0
rx-1519-max: 0
rx-too-long: 0
rx-unicast: 17 374 754 36 277 360 3 754 257 766 038 32 293 871 0 0 0 0 0
rx-broadcast: 35 697 796 25 895 575 4 220 0 0 0 0 0 0
rx-pause: 0 0 0 0 0 0 0 0 0 0 0
rx-multicast: 4 651 3 719 109 801 12 886 3 265 0 0 0 0 0 0
rx-fcs-error: 0 0 2 096 0 0 0 0 0 0 0 0
rx-align-error: 0
rx-fragment: 0 0 1 008 0 0 0 0 0 0 0 0
rx-unknown-op: 0 0 0 0 0 0 0 0 0 0
rx-length-error: 0
rx-code-error: 0 0 0 0 0 0 0 0 0 0
rx-jabber: 0 0 27 0 0 0 0 0 0 0 0
rx-drop: 0 0 0 0 0 0 0 0 0 0 0
tx-bytes: 1 676 532 302 54 793 690 390 10 726 274 973 1 342 382 663 13 155 704 053 0 0 0 0 0 0
tx-packet: 0
tx-unicast: 7 397 717 40 236 221 7 278 505 1 155 175 34 078 993 0 0 0 0 0
tx-broadcast: 6 22 690 6 980 32 242 31 946 0 0 0 0 0 0
tx-pause: 0 0 0 0 0 0 0 0 0 0 0
tx-multicast: 0 150 176 107 344 204 068 261 262 0 0 0 0 0 0
tx-collision: 0 0 0 0 0 0 0 0 0 0
tx-excessive-collision: 0 0 0 0 0 0 0 0 0 0
tx-multiple-collision: 0 0 0 0 0 0 0 0 0 0
tx-single-collision: 0 0 0 0 0 0 0 0 0 0
tx-deferred: 0 0 0 0 0 0 0 0 0 0
tx-late-collision: 0 0 0 0 0 0 0 0 0 0
tx-drop: 0 0 0 0 0 0 0 0 0 0
tx-rx-64: 618 426 107 951 91 650 531 742 141 419 0 0 0 0 0
tx-rx-65-127: 6 696 739 31 542 157 3 828 972 130 162 29 512 116 0 0 0 0 0
tx-rx-128-255: 342 698 759 811 108 818 106 804 694 030 0 0 0 0 0
tx-rx-256-511: 158 227 124 300 16 583 27 821 129 627 0 0 0 0 0
tx-rx-512-1023: 179 743 823 622 11 047 8 633 698 079 0 0 0 0 0
tx-rx-1024-1518: 16 816 992 43 333 121 7 227 781 1 365 822 35 498 286 0 0 0 0 0

[Jerry]

Ten switch bol myslený na test, že či sa to bude správať rovnako. Aby nebol pripojený priamo do mk.
Pokiaľ nemáš, nekupuj zbytočne switch. Btw switch tplink tak isto neber pokiaľ máš mikrotik, je toho všade popísané dosť, že mikrotik a tplink sa nemajú moc radi a dejú sa rôzne anomálie.

PS: necutuj posledný príspevok, ďakujem

[mp3turbo]

nieco sa deje na tom tretom ethernete s Xboxom : rx-fcs-error: 0 0 2 096 0 0 0 0 0 0 0 0

toto je najcastejsie sposobene doje-pokazenym kablom, nekvalitnym krimpovanim pripaadne presluchmi z toho vyplyvajucimi, nesuladom medzi nastavenou rychlostou a duplexom na switchi a na zariadeni.

Vyskusat kabel asi mozes relativne jednoducho - na hulvata natiahni krizom cez dom/byt nejaky docasny, bacha nech sa volakto nezabije - ved vyskusat rychlost na xboxe neni robota na tri dni. Desat minut to vydrzia. Ak nepomoze kabel, skusil by som zmenit nastavenie eth4 portu, teraz tam mas :


3 RS ;;; Xbox serie x
name="ether4" default-name="ether4" mtu=1500 l2mtu=1592 mac-address=2C:C8:1B:AB:96:49 orig-mac-address=2C:C8:1B:AB:96:49 arp=enabled arp-timeout=auto
loop-protect=default loop-protect-status=off loop-protect-send-interval=5s loop-protect-disable-time=5m auto-negotiation=yes
advertise=10M-half,10M-full,100M-half,100M-full,1000M-half,1000M-full full-duplex=yes tx-flow-control=off rx-flow-control=off speed=1Gbps bandwidth=unlimited/unlimited


vypol by som auto-nego a vnutil natvrdo 1000M-full. Ak sa xbox nepripoji, treba aj na nom zmenit nastavenia na manual settings, 1000Mbit, fullduplex.
Takisto by sa mohlo stat ze mas chyteny port, mas tam dost volnych tak by som proste prehodil Xbox do ineho portu, prehodil IP adresu (/ip address) zo sucasneho ether4 na ten novy port a hajde skusat.

Ak nepomoze, zapol by som TX aj RX Flow control. Poznamka : tieto nastavenia typicky nie je potrebne robit, tuto mas specificky pripad.


edit : este sa moze stat, ze sa ti do kabla indukuje bordel - napriklad ak mas tahany ethernet paralelne s 240V rozvodmi. Aj napriek tomu ze je ten ethernet tieneny.

[Pavoluhliarik]

Myslím, že to tým mikrotikom není lebo som teraz vybral kábel z mikrotiku čo mám od operátora a dal som ho na priamo do xboxu tak je to to isté takže to ne bud emikrotikom bude to asi niečo s xboxom.

[Jerry]

Skúsil si aj ten iný port v mikrotiku ako radil turbo?

[Pavoluhliarik]

Skúšal som to na dvoch stejnakých mikrotikoch takže to nebude mikrotik ako som to opísal vyžšie.

[mp3turbo]

cize nebude to konkretny kus pokazeny - ale furt to boli dva JEDNAKE mikrotiky co je samozrejme problem pre troubleshooting. Potrebujes INAKSIE zariadenia (idealne nic co ma na sebe napisane Mikrotik) aby si mohol vyvodit nejaky rozumny zaver.

Cize aby to nebola nejaka uzasna vlastnost mikrotikov voci specifickemu cipu / firmware toho IksBoksa pisal som to, nabohovali sme sa ako kone ked sme prepajali Cisco s Intel adaptermi v serveroch. Tam chodi auto nego, tam nechodi, firmware specific, dve rozlicne verzie firmware proti dvom rozlicnym verziam na druhej strane sa spravaju inak, proste styri kombinacie maximum

Ked mozes, pichni to nejako mimo mikrotiku (priamo do radia ?) a ked mozes, tak zmen tu autonego. Neni to ziadna namaha, dvadsat sekund aj s prihlasenim. Nic sa nezlepsi, tak das naspat.

V kazdom pripade tam su ERROR COUNTERY na tvojom mikrotiku a prislusnom porte s IksBoksom - a nie zrovna malo. Ako pisem : kabel, indukcia, konektory, normalna vec, stava sa. Mozno si zariadenia nerozumeju co by sa nemalo stat po 20 rokoch existencie gigabitu, ale...

[Pavoluhliarik]

Preboha veď som napísal, že to robí aj keď to neni napojené v mikrotiku.

[16cmfan]

Este skus ci neni nejaky novy FW na xbox resp updaty + urcite by som cekol nastavenia na strane xboxu

[Pavoluhliarik]

Xbox je aktuálny jedine ho len dať do výrobných nastaveni a to skúsim ale až o mesiac