Asus P5E3 a 1600MHz FSB
- Trubka
- Nový používateľ
- Príspevky: 188
- Dátum registrácie: Št 27. Dec, 2007, 08:00
- Bydlisko: BA-Rusovce
Asus P5E3 a 1600MHz FSB
Mam procesor C2D E8400 a chcem ho posunut na 3.6GHz zvysenim FSB z 1333 na 1600 MHz. Ale ked v BIOSe nastavim FSB na 400MHz tak pocitac chvilu ide a potom zmrzne. Procesoru pustam 1.25V a je chladeny pomocou Zalmanu reseratora 1v2. Pamate mam na referencnych hodnotach: 1333MHz 9-9-9-24 pri 1.7V. Takto sa sprava az po update BIOSu na 1002 verziu (dovtedy sa 400MHz FSB ani nedalo dosiahnut, overclocking failed a konec). Ale teraz neviem v com moze byt problem pretoze chipset chladim dostatocne, tiez vodou. Podla mna to moze byt napatim chipsetu (mam na auto), alebo procesoru (ten som nechcel nad referencne hodnoty. Ake je bezpecne napatie na tom procesore?
mas pravdepodobne malo V na vCore... pridaj voltaz na CPU... do tych 1.35-1.4V ... dalo by sa aj viac, ale najprv to skus... a mas vodu, tak by nemal byt problem... hlavne sleduj teploty...
vFSB daj na 1.3V
vNB na 1.4V (tam mas asi tiez vodu)
ostatne auto... pri tomto by Ti mala dat doska 400FSB bez problemov... a ostatne features mas dufam povypinane...
vFSB daj na 1.3V
vNB na 1.4V (tam mas asi tiez vodu)
ostatne auto... pri tomto by Ti mala dat doska 400FSB bez problemov... a ostatne features mas dufam povypinane...
DFI X58 | i7 920 @ 4.4GHz | GTX 260
Taktovanie Intel C2D/C2Q procesorov
P5Q Deluxe Discussion | LN2 - Invex 2008 | OC Sessions
Taktovanie Intel C2D/C2Q procesorov
P5Q Deluxe Discussion | LN2 - Invex 2008 | OC Sessions
- Trubka
- Nový používateľ
- Príspevky: 188
- Dátum registrácie: Št 27. Dec, 2007, 08:00
- Bydlisko: BA-Rusovce
ostatne mam na "auto"
ja som nechal na stock napati preto, lebo som cital myslim v PCrevue alebo kde ze penryny idu dobre aj bez zmeny napatia, alebo to bol extreme s odomknutym nasobicom
aj napatie na northbridge mam na auto lebo som nevedel kolko to znese (ale tu vodu mam zakladny zalman blok hlinikovy na NB a na CPUhttp://www.zalman.com/ENG/product/Product_Read.asp?idx=180).
ja som nechal na stock napati preto, lebo som cital myslim v PCrevue alebo kde ze penryny idu dobre aj bez zmeny napatia, alebo to bol extreme s odomknutym nasobicom
aj napatie na northbridge mam na auto lebo som nevedel kolko to znese (ale tu vodu mam zakladny zalman blok hlinikovy na NB a na CPUhttp://www.zalman.com/ENG/product/Product_Read.asp?idx=180).
skusil by som nieco take:
AI Overclocking: Manual
CPU Ratio Control: Manual
- Ratio CMOS Setting: 9
FSB Frequency: 400
PCI-E Frequency: 100
DRAM Frequency: tu podla delicky, aby ti vyslo nieco do tych 1333, kludne aj menej, napr. 1200MHz...
DRAM Timing Control: Manual
CAS# Latency: 9
RAS# to CAS# Delay: 9
RAS# Precharge: 9
RAS# Activate to Precharge: 24
TWR: AUTO
TRFC: AUTO
TWTR: AUTO
TRRD: AUTO
TRTP: AUTO
DRAM Static Read Control: Disabled
Transaction Booster: AUTO
Clock Over-Charging Mode: AUTO
CPU Spread Spectrum: Disabled
PCIE Spread Spectrum: Disabled
CPU Voltage: 1.3-1.4V , sleduj teploty!!!
CPU Voltage Reference: AUTO
CPU Voltage Damper: Enabled
CPU PLL Voltage: 1.50v
DRAM Voltage: 1.7V
FSB Termination Voltage: 1.30v
North Bridge Voltage: 1.40v
North Bridge Voltage Reference: AUTO
South Bridge Voltage: AUTO
Advance CPU Settings
CPU Ratio Control: Manual
- Ratio CMOS Setting: 9
C1E Suppport: Disabled
Max CPUID Value Limit: Disabled
Vanderpool Technology: Disabled
CPU TM Function: Disabled
Execute Disable Bit: Disabled
PECI: Enabled
:roll:
AI Overclocking: Manual
CPU Ratio Control: Manual
- Ratio CMOS Setting: 9
FSB Frequency: 400
PCI-E Frequency: 100
DRAM Frequency: tu podla delicky, aby ti vyslo nieco do tych 1333, kludne aj menej, napr. 1200MHz...
DRAM Timing Control: Manual
CAS# Latency: 9
RAS# to CAS# Delay: 9
RAS# Precharge: 9
RAS# Activate to Precharge: 24
TWR: AUTO
TRFC: AUTO
TWTR: AUTO
TRRD: AUTO
TRTP: AUTO
DRAM Static Read Control: Disabled
Transaction Booster: AUTO
Clock Over-Charging Mode: AUTO
CPU Spread Spectrum: Disabled
PCIE Spread Spectrum: Disabled
CPU Voltage: 1.3-1.4V , sleduj teploty!!!
CPU Voltage Reference: AUTO
CPU Voltage Damper: Enabled
CPU PLL Voltage: 1.50v
DRAM Voltage: 1.7V
FSB Termination Voltage: 1.30v
North Bridge Voltage: 1.40v
North Bridge Voltage Reference: AUTO
South Bridge Voltage: AUTO
Advance CPU Settings
CPU Ratio Control: Manual
- Ratio CMOS Setting: 9
C1E Suppport: Disabled
Max CPUID Value Limit: Disabled
Vanderpool Technology: Disabled
CPU TM Function: Disabled
Execute Disable Bit: Disabled
PECI: Enabled
:roll:
DFI X58 | i7 920 @ 4.4GHz | GTX 260
Taktovanie Intel C2D/C2Q procesorov
P5Q Deluxe Discussion | LN2 - Invex 2008 | OC Sessions
Taktovanie Intel C2D/C2Q procesorov
P5Q Deluxe Discussion | LN2 - Invex 2008 | OC Sessions