DFI Lanparty a i7 920

[MaxPayne]

Takze mam tuto dosku LANPARTY UT X58-T3eH8 ,core i7 920 c0, ramky kingston-6gb-kit-ddr3-2000mhz-cl9 ,chladic Noctua NH-U12P SE1366
nastavenie biosu takto :
CPU Feature
Set VR Current Limit Max: Disabled
Thermal Management Control: Disabled
EIST Function: Disabled
CxE Function: Disabled
Execute Disable Bit: Disabled
Virtualization Technology: Disabled

***** Logical Processor Setting *****
Intel HT Technology: Enabled
Active Processor Cores: All

DRAM Timing
Memory Control Setting: AUTO
Memory LowGap: 1536M

DRAM Command Rate: AUTO
CAS Latency Time (tCL): 9
RAS# to CAS# Delay (tRCD): 9
RAS# Precharge (tRP): 9
Precharge Delay (tRAS): 24
REF to ACT Delay (tRFC): AUTO
Write to PRE Delay (tWR): AUTO
Rank Write to Read (tWTR): AUTO
ACT to ACT Delay (tRRD): AUTO
Row Cycle Time (tRC): AUTO
Read CAS# Precharge (tRTP): AUTO
Four ACT WIN Time (tFAW): AUTO

Voltage Setting
O.C. Shut Down Free: Enable O.C.S.D.F
CPU VID Control: 1,375V
CPU VID Special Add Limit: Enabled
CPU VID Special Add: Auto
Vcore Droop Control: Enabled
DRAM Bus Voltage: 1.680v
DRAM PWM Switch Frequency: Nominal
DRAM PWM Phase Control: 2 Phase Operation
CPU VTT Special Add: AUTO
CPU VTT Voltage: 1.44v
VTT PWM Switch Frequency: Nominal
VTT PWM Phase Control: 2 Phase Operation
CPU PLL Voltage: 1.80v
IOH/ICH 1.1V Voltage: 1.11v
IOH Analog Voltage: 1.10v
ICH 1.5 Voltage: 1.5v
ICH 1.05V Voltage: 1.05v
DIMM 1/2 DQ/DQSTB Bus VREF: -00.0%
DIMM 3/4 DQ/DQSTB Bus VREF: -00.0%
DIMM 5/6 DQ/DQSTB Bus VREF: -00.0%
ADDR/CMD VREF Control: Disabled
x DIMM 1/2 ADDR/CMD Bus VREF: 110
x DIMM 3/4 ADDR/CMD Bus VREF: 110
x DIMM 5/6 ADDR/CMD Bus VREF: 110
CPU QPI Drive Strength: Normal
IOH QPI Drive Strength: Normal

Exit Setup Shut down: Mode 2
O.C. Fail Retry Counter: Enabled
O.C. Fail CMOS Reload: Disabled

PPM Function: Enabled
Turbo Mode Function: Disabled
1 core Max Turbo Ratio: 22x
2 core Max Turbo Ratio: 21x
3 core Max Turbo Ratio: 21x
4 core Max Turbo Ratio: 21x
CPU Non-Turbo Clock Ratio: 20x

* BCLK/UCLK/QPI Controller Settings *
QPI Control Settings: Enabled
QPI Link Fast Mode: Enabled
QPI Frequency: AUTO
CPU Base Clock (BCLK): 200 Mhz
Boot Up CPU Base Clock: AUTO
PCIE Clock: 100 Mhz
DRAM Frequency: 1200Mhz
Uncore Frequency: 2400Mhz

CPU Spread Spectrum: Disabled
PCIE Spread Spectrum: Disabled

problem je ten ze pc nabotuje do win ale ked spustim prime95 64bit pod vista64 hned zamrzne comp a hodi modru obrazovku ohladom memory dump a percenta skacu,neviete kde je chyba? palee skus poradit

[dexterav]

prečo myslíš že ten CPU ti pôjde 4,2GHz + turbo na 1,375V
hlavne ked to je C0

[MaxPayne]

turbo je vypnute a napatie som daval aj 1.44 a stale to iste tam bude inde chyba ale neviem kde

[dexterav]

tak či tak dosť vysoká frekvencia 4.2ghz na C0 proste to skús na 4ghz

[MaxPayne]

zistil som ze problem bude v pamatiach zrejme ked ich podtakujem tak to ide zatial stabilne na 3.8ghz

[dexterav]

no lenže si znížil aj frekvenciu CPU

[MaxPayne]

dal som cpu voltage na 1.3v vo win ukazuje 1.34v,nasobic mam 19x200 a ramky idu 1600mhz a 3200mhz uncore zatial stabilne aj ked teplota v zatazi na prime95 je okolo 80 stupnov

[MaxPayne]

takze to nastavenie nebolo stabilne toto uz je
nastavenie biosu takto :
CPU Feature
Set VR Current Limit Max: Disabled
Thermal Management Control: Disabled
EIST Function: Disabled
CxE Function: Disabled
Execute Disable Bit: Disabled
Virtualization Technology: Disabled

***** Logical Processor Setting *****
Intel HT Technology: Enabled
Active Processor Cores: All

DRAM Timing
Memory Control Setting: AUTO
Memory LowGap: 1536M

DRAM Command Rate: AUTO
CAS Latency Time (tCL): AUTO
RAS# to CAS# Delay (tRCD): AUTO
RAS# Precharge (tRP): AUTO
Precharge Delay (tRAS): AUTO
REF to ACT Delay (tRFC): AUTO
Write to PRE Delay (tWR): AUTO
Rank Write to Read (tWTR): AUTO
ACT to ACT Delay (tRRD): AUTO
Row Cycle Time (tRC): AUTO
Read CAS# Precharge (tRTP): AUTO
Four ACT WIN Time (tFAW): AUTO

Voltage Setting
O.C. Shut Down Free: Enable O.C.S.D.F
CPU VID Control: 1,250V
CPU VID Special Add Limit: Enabled
CPU VID Special Add: Auto
Vcore Droop Control: Enabled
DRAM Bus Voltage: 1.680v
DRAM PWM Switch Frequency: Nominal
DRAM PWM Phase Control: 2 Phase Operation
CPU VTT Special Add: AUTO
CPU VTT Voltage: 1.21v
VTT PWM Switch Frequency: Nominal
VTT PWM Phase Control: 2 Phase Operation
CPU PLL Voltage: 1.80v
IOH/ICH 1.1V Voltage: 1.11v
IOH Analog Voltage: 1.10v
ICH 1.5 Voltage: 1.5v
ICH 1.05V Voltage: 1.05v
DIMM 1/2 DQ/DQSTB Bus VREF: -00.0%
DIMM 3/4 DQ/DQSTB Bus VREF: -00.0%
DIMM 5/6 DQ/DQSTB Bus VREF: -00.0%
ADDR/CMD VREF Control: Disabled
x DIMM 1/2 ADDR/CMD Bus VREF: 110
x DIMM 3/4 ADDR/CMD Bus VREF: 110
x DIMM 5/6 ADDR/CMD Bus VREF: 110
CPU QPI Drive Strength: Normal
IOH QPI Drive Strength: Normal

Exit Setup Shut down: Mode 2
O.C. Fail Retry Counter: Enabled
O.C. Fail CMOS Reload: Disabled

PPM Function: Enabled
Turbo Mode Function: Disabled
1 core Max Turbo Ratio: 22x
2 core Max Turbo Ratio: 21x
3 core Max Turbo Ratio: 21x
4 core Max Turbo Ratio: 21x
CPU Non-Turbo Clock Ratio: 20x

* BCLK/UCLK/QPI Controller Settings *
QPI Control Settings: Enabled
QPI Link Fast Mode: Enabled
QPI Frequency: AUTO
CPU Base Clock (BCLK): 180 Mhz
Boot Up CPU Base Clock: AUTO
PCIE Clock: 100 Mhz
DRAM Frequency: 1440Mhz
Uncore Frequency: 2880Mhz

CPU Spread Spectrum: Disabled
PCIE Spread Spectrum: Disabled

problem je v poslednych nastaveniach delickach pamate,ked to chcem zdvihnut na 1800mhz a uncore 3600mhz pc ani nenabotuje,co musis zdvyhnut aby to islo? napatie na ram nepomaha

[dexterav]

uncore cez 3400 nerobí dobrotu

[MaxPayne]

dexter preco? ved co pozeram testy na webe tam davaju aj 3800mhz

[dexterav]

krátkodobo ano, dlhodobo...
umňa nejde už 3500 dosť je to nestabilné potom...