Nataktovanie Q6600

[Bird]

po 5 minutach mi ukaze detected error a v normalnom cpu: occt po30 sekundach

[Borec]

tak ej to nestabilné

[Bird]

pravdepodobne ram. aj sa mi restartovava ale prehrievanie to neni neni an pretoaktovany moj cpu. ale v nudzovom rezime vydrzi dlhis e

[tommyk999]

Caute, mohol by mi niekdo z vas poradit ako nataktovat Q6600 na ASUS P5Q PRO? Alebo poslat nastavenia. Chcel by som dosiahnut takt tych 3.6ghz, ale mam taky problem ze procesor si pyta velmi vela napatia. Ked dam napatie pod 1.5V nedam z neho ani 3.46ghz.
Moze to byt tym ze mam napajanie len 4 pin? Stale ked chcem nabehnut do windowsu pri vyssich taktoch vyhodi mi modru tabulku, pri takte tych 3.5 na napati 1.52V sa da hrat, obcas vyhodi tabulku, ale OCCT padne po minute a pol. Viem ze keby som asi zvysil napatie tak to ide stabilnejsie, ale nemam vodne chladenie tak viac davat nechcem. Kedze som videl nataktovany tento CPU na 3.6 aj na napati 1.4V tak to nejak musi ist. Dakujem za kazdu radu.

Skus tieto nastavenia, mne to zatial preslo Intel burn test maximum s 69 C max, este to necham bezat v Prime95 aby som si bol isty ze to je stabilne.

Ai Overclock Tuner [manuall]
CPU Ratio Setting [09.0]
FSB Frequency [400]
PCIE Frequency [101]
FSB strap to north bridge [333] this is easiest to maintain stabiliy but can be left auto (if left at auto the DRAM Frequency would be 1066)

DRAM Frequency [961]
DRAM Timing Control [AUTO]

DRAM Static Read Control [AUTO]
DRAM Read Training [AUTO]
Mem. OC Charger [AUTO]
Ai Clock Twister [LIGHT]
Ai Transaction Booster [MANUALL}
Common Performance Level [11]

ALL PULL-IN SET TO ENABLED

CPU Voltage [AUTO]
CPU GLT Reference [AUTO]
CPU PLL Voltage [1.54] Do NOT leave auto as that massively overvolts
FSB Termination Voltage [1.24] Do NOT leave auto as that massively overvolts
NB Voltage [1.26]
SB Voltage [1.10]
PCIE SATA Voltage [1.50]

Load Line Calibration [Enabled]
CPU Spread Spectrum [Disabled]
PCIE Spread Spectrum [Disabled]
CPU Clock Skew [AUTO]
NB Clock Skew [AUTO]
CPU Margin Enhancement [Performance Mode]

[Lucky007]

Diky, ale ja som zistil ze som mal zle nastavenia mal som nestabilne ramky, teraz to mam uplne stabilen na 3.4.

[tommyk999]

Mozes mi poslat nastavenie tvojho biosu na porovnanie s mojim kde mam stabilne 3.2? Dik

[Lucky007]

Ai Overclock Tuner [manuall]
CPU Ratio Setting [08.0]
FSB Frequency [425]
PCIE Frequency [101]
FSB strap to north bridge AUTO
DRAM Frequency [1071]
DRAM Timing Control [AUTO]

DRAM Static Read Control [AUTO]
DRAM Read Training [AUTO]
Mem. OC Charger [Enabled]
Ai Clock Twister [AUTO]
Ai Transaction Booster [AUTO]
Common Performance Level [AUTO]

ALL PULL-IN SET TO ENABLED

CPU Voltage [1.45V]
CPU GLT Reference [x63]
CPU PLL Voltage [1.54] Do NOT leave auto as that massively overvolts
FSB Termination Voltage [1.30] Do NOT leave auto as that massively overvolts
NB Voltage [1.30]
SB Voltage [AUTO]
PCIE SATA Voltage [AUTO]

Load Line Calibration [Enabled]
CPU Spread Spectrum [Disabled]
PCIE Spread Spectrum [Disabled]
CPU Clock Skew [AUTO]
NB Clock Skew [AUTO]
CPU Margin Enhancement [Compatible]

[Jerry]

Na ziadost zakaladatela LOCK ....