Asrock 939A785GMH/128M a Integrovana karta

[Gudas]

Vážne?
http://zone.ni.com/devzone/cda/tut/p/id/4154

Dôležité je to iba pri pretaktovaní, keď by sa aj malý posun v základnom takte mohol postarať o nestabilitu. Ide však o funkciu na potlačenie elmg. rušenia, nie "obmedzovač výkonu na 95%"

[mano8]

vysledkom je male obmedzenie, ja to viem ale skus to vysvetlit jemu.
intel vyriesil tieto sracky ovladanim PLL napetia, ktore dodatocne stabilizuje frequenciu aj v plnom vykone..

[Alexnext65]

vysledkom je male obmedzenie, ja to viem ale skus to vysvetlit jemu.
intel vyriesil tieto sracky ovladanim PLL napetia, ktore dodatocne stabilizuje frequenciu aj v plnom vykone..

Skusal som to zapnut aj vypnut a furt mi to sekalo.Nakoniec som to tak vyriesil ze som vsetky ide koncovky dal na sata port.Cize
DVD napalovacka a hdd.Zatial mi to ide uz tyzden a pohode.Len nechapem ked mam moznost napojit na ide port tak preco mi to robilo.Proste ako keby disk zaostaval a dlhy start.Keby daco tak pisem.Inac mam jednu otazku ohladom predneho panela na audio a mic.
Ked zapojim sluchatka nereaguje to aj microfon.Cital som v navode ze treba pouzivat koncovku AC97 a pointa je taka ci som to dobre pochopil.
To je v navode

1. High Definition Audio supports Jack Sensing, but the panel wire on
the chassis must support HDA to function correctly. Please follow the
instruction in our manual and chassis manual to install your system.
2. If you use AC’97 audio panel, please install it to the front panel audio
header as below:
A. Connect Mic_IN (MIC) to MIC2_L.
B. Connect Audio_R (RIN) to OUT2_R and Audio_L (LIN) to OUT2_L.
C. Connect Ground (GND) to Ground (GND).
D. MIC_RET and OUT_RET are for HD audio panel only. You don’t
need to connect them for AC’97 audio panel.
E. Enter BIOS Setup Utility. Enter Advanced Settings, and then select
Chipset Configuration. Set the Front Panel Control option from
[Auto] to [Enabled].
F. Enter Windows system. Click the icon on the lower right hand
taskbar to enter Realtek HD Audio Manager.
For Windows® XP / XP 64-bit OS:
Click “Audio I/O”, select “Connector Settings” , choose
“Disable front panel jack detection”, and save the change by
clicking “OK”.
For Windows® VistaTM / VistaTM 64-bit OS:
Click the right-top “Folder” icon , choose “Disable front
panel jack detection”, and save the change by clicking “OK”.
G. To activate the front mic.
For Windows® XP / XP 64-bit OS:
Please select “Front Mic” as default record device.
If you want to hear your voice through front mic, please deselect "Mute"
icon in “Front Mic” of “Playback” portion.
For Windows® VistaTM / VistaTM 64-bit OS:
Go to the "Front Mic" Tab in the Realtek Control panel.
Click "Set Default Device" to make the Front Mic as the default record
device.

[Alexnext65]

Ahoj konecne vsetko funguje.PC som odnesol do servisu a potom ku mame.Vsade a vsetko pohode.Odnesol som domov {RD} napojil a blblo to.
Nahodou som zapotil ze skusim pc zdroj vymenit a ide pohode.Proste novy zdroj a blbne to.Nechapem kam ten svet speje.Predny panel mi poriesily v servise.Vedlajsiu kraficku kartu odpojim neskor asi ked budem instalovat novy win xp.Takze ked sa dari tak sa dari.Caf

PS.Tolko casu a nervov stratit neprajem nikomu.